x:panda
TM
English manual
G
B
© 2012 R82 A/S. All rights reserved.
The R82 logo and the x:panda chairs are trademarks of R82 A/S.
11.2016 - rev. 016
Pat. pend.
U.S. Patent Des. D598,680 S
Pat. Pend.
GB
X:PANDA
x:panda is a multiadjustable seat, delivered in 4 different sizes. Each seat adjusts
in 3 different widths and stepless in seat depth.
G
B
The back is dynamic, making it possible for the child to extend and push back
against relatively light resistance and then recover into the desired sitting position.
Furthermore the back angles to make it possible to place the child with either an
open or closed hip angle. When angling the seat and the base it is possible to
create the desired working or resting position.
The many adjustment possibilities and wide range of accessories makes it possible
to adjust the seat to an individual child’s need for comfort and support.
The seat fits on a variety of seat bases from R82, making it suitable for both indoor
and outdoor use.
Indoor use High-low:x indoor frame
Outdoor use High-low:x outdoor frame
Combi Frame
Serval Buggy frame
This manual will enable you to take full advantage of the many possibilities of the
x:panda. Therefore, we recommend that you read this manual before using the
frame.
2
GB
CONTENTS
Safety...................................................................................................................4
Tools.....................................................................................................................4
Warranty...............................................................................................................4
Ready for use.......................................................................................................5
Back recline..........................................................................................................6
Back height adjustment........................................................................................6
Hip supports - Individual adjustment....................................................................7
Leg supports - individual adjustment....................................................................7
Head supports......................................................................................................8
Back width extension............................................................................................8
Fixed side supports..............................................................................................9
Quick locks for fixed side supports.......................................................................9
Upper arm support for the fixed side supports ....................................................9
Swing-away side supports..................................................................................10
Quick locks for swing-away side supports..........................................................10
Arm rest..............................................................................................................11
Tray, swing-away................................................................................................12
Tray, two-rod system..........................................................................................12
Arm rest for tray..................................................................................................13
Toybar for tray....................................................................................................13
Grip handle for tray.............................................................................................13
Vests & belts.......................................................................................................14
Fixlock fittings.....................................................................................................14
Seat wedges.......................................................................................................15
Seat strap...........................................................................................................15
Foam back plate.................................................................................................16
Cover plate.........................................................................................................16
Lumbar support..................................................................................................16
Non-dynamic gas spring.....................................................................................17
Fixed rod............................................................................................................17
x:panda mounted on High-low:x.........................................................................18
Mounting the seat on the High-low:x size 3 .......................................................19
Growth from one size to another - width adjustment.........................................20
Growth from one size to another - depth adjustment........................................21
Replacement of back - one size to another........................................................22
The x:panda seat on High-low:x frames.............................................................23
The x:panda seat on Panda Fututra High-low frames........................................24
The x:panda seat on Combi Frame:x.................................................................25
The x:panda seat on buggy frame......................................................................26
Transportation in motor vehicles........................................................................27
Position the back before transportation..............................................................28
Transport fittings on a buggy frame....................................................................28
Transport fittings on the Combi Frame:x............................................................29
Secure the product in the vehicle.......................................................................30
Secure the child in the Product..........................................................................31
Product identification..........................................................................................32
Product identification..........................................................................................33
Measurements....................................................................................................34
Technical data....................................................................................................35
Producer.............................................................................................................35
Distributor...........................................................................................................35
Maintenance.......................................................................................................36
3
G
B
GB
SAFETY
The x:panda has earned the CE-mark. This certifies that it meets all relevant European
safety requirements.
The durability of this product is 5 years when it is used on a daily basis. Hereafter the product
must be renovated (by R82 personnel) to extend the lifetime.
Remove the CE-mark, when rebuilding the product or when using other than original
R82 spare parts and fittings.
The x:panda is constructed for one user only. Do not place more than one user in
the x:panda.
Never leave your child unattended in this product. Ensure constant supervision by
an adult. Incorrect use of the product, may cause serious injury to the user. Ensure
that the belt is securely fixed to the product before every use.
Any adjustments and addition of accessories which are not described in this manual,
must only be made by authorized R82 personnel. Vests and belts must be mounted
according to the instruction provided with the products.
The latest version of the manual is always available online:
www.R82.com
GB
G
B
WARRANTY
R82 offers a 2-year warranty against defects in workmanship and materials. The warranty
would be adversely affected if the customer’s responsibility of servicing and/or daily maintenance is not carried out according to the guidelines and intervals prescribed by the supplier and/or stated in the manual. For further information, we refer to the R82 homepage/
download. The warranty can only be sustained if the R82 product is in use in the same
country where it was purchased and if the product can be identified by the serial number.
The warranty does not cover accidental damage, including damage caused by misuse or
neglect. The warranty does not extend to non-durable parts, which are subject to normal
wear and tear and need periodic replacement. The warranty is null and void if non-original
R82 parts/accessories are used, or if the product is repaired or altered by anyone other
than an authorised R82 representative or by trained personnel officially recognised by R82
for repair and maintenance of R82 products. R82 reserves the right to inspect the product
being claimed for and the relevant documentation before agreeing to the warranty claim,
and to decide upon whether to replace or repair the defective product. It is the customer’s
responsibility to return the item being claimed for under warranty to the address of purchase.
The warranty is given by R82 or, subsequently, an R82 dealer.
GB
TOOLS
Use the 5 mm Allen key placed beneath the seat unit, to perform all adjustments described
in this manual.
4
GB
READY FOR USE
The x:panda is delivered so that it takes up
minimum space during transport. Follow the
instructions below to unpack the x:panda.
* Remove the x:panda from the box
* Adjust the back angle (A)
A
* Adjust the back height (B)
* Adjust the seat depth (C)
* Adjust the leg angle (D)
Further instructions can be found on page 6+7.
The x:panda is now ready for use once you have
fully read this manual.
B
G
B
C
D
5
GB
C
BACK RECLINE
Release the handle (A) to recline the back.
D
Firmly grab hold and support the back of
the chair before releasing the handle to
prevent sudden recline.
The release handle is equipped with a security
lock (B). Turn the lock to the left and it is activated, turn it to the right and it is deactivated.
Always activate the lock after adjustment.
A
The back on x:panda has dynamic movement.
Move the small ring (C) up or down to adjust the
range of movement.
B
When reclining the back, please be carefull
not to get fingers caught between the gas
spring and the seat (D).
GB
G
B
A
BACK HEIGHT
ADJUSTMENT
Loosen the bolts (A) and (B) to adjust the height
of the back.
Fasten all bolts at the desired height.
i
B
6
Do not remove any of the bolts - only
loosen to adjust.
GB
HIP SUPPORTS
- INDIVIDUAL
ADJUSTMENT
A
Angle, depth and width adjustment:
Loosen the bolts (A) to adjust. Fasten at the
desired position.
i
Do not remove any of the bolts - only
loosen to adjust.
GB
LEG SUPPORTS
- INDIVIDUAL
ADJUSTMENT
G
B
Angle and depth adjustment:
Loosen the bolt (A) to adjust. Fasten at the desired position.
A
Width adjustment:
Remove the bolt (B) to adjust. Fasten at the
desired position.
i
B
Do not remove any of the bolts (A) - only
loosen to adjust.
7
GB
HEAD SUPPORTS
Mounting and height adjustment:
Loosen the handle (A).
Angle adjustment:
Loosen the screws (B) and (C) with a spanner.
D
C
Sideways adjustment:
Loosen the screw (D).
B
Fasten all screws at the desired position.
A
When adjusting the head support, please
be carefull not to get fingers caught between the back of the chair and the head
support fiitting.
GB
G
B
BACK WIDTH
EXTENSION
ONLY SIZE 4
A
Mount the back width extension and fasten the
screws (A) on the back. Make sure the extension
is pushed all the way in before fastening.
8
GB
FIXED SIDE
SUPPORTS
A
Height adjustment:
Remove the bolts (A).
Place the supports in the desired position and
remount the bolts.
Width adjustment:
Loosen the bolts (A).
Fasten at the desired position.
GB
QUICK LOCKS
FOR FIXED SIDE
SUPPORTS
A
Height adjustment:
Remove the bolts (A).
Place the side supports with quick locks in the
desired position and remount the bolts.
B
Width adjustment:
Pull the quick lock handle up (B).
Lock the handle down when the support is in the
desired position.
GB
UPPER ARM
SUPPORT FOR
THE FIXED SIDE
SUPPORTS
The upper arm supports is developed as an
accessory to seats produced later than December 2008, i.e. for seats delivered before
this period, you will need a new set of side
supports in order to mount the upper arm
supports.
9
G
B
GB
SWING-AWAY SIDE
SUPPORTS
Height adjustment:
Remove the bolts (A).
Place the supports and remount the bolts.
A
B
Width adjustment:
Loosen the bolts (A).
Fasten at the desired position.
Swing-away function:
Press the red button (B) to release.
The carer should check and oil (synthetic
oil) the swing away parts occationally - at
least every 3 months.
GB
G
B
QUICK LOCKS FOR
SWING-AWAY SIDE
SUPPORTS
Height adjustment:
Remove the bolts (A).
Place the side supports with quick locks and
remount the bolts.
Width adjustment:
Pull the quick lock handle up (B).
Lock the handle in the desired position.
A
B
10
GB
ARM REST
Size 1+2+3
Height adjustment:
Loosen the screw (A) and move it into desired
height position. Fasten the screw.
Loosen handle/screw (C) to move the arm rest
into position. Fasten the handle/screw (handtight).
D
B
Angling the arm rest cushion:
Loosen the handle (B).
A
C
Angling the arm rest bar (only size 1+2+3):
Loosen the handle/screw (C).
Size 4
Adjust the arm rest cushion:
Loosen the screws (D) beneath the armpad.
When adjusting the arm rest, please be
carefull not to get fingers caught between
the chair and the armpad.
D
B
C
Size 4
D
11
G
B
GB
TRAY, SWING-AWAY
ONLY FOR SIZE 1+2+3
A) Mounting and depth adjustment
B)Width adjustment
C) Angling the tray, by angling the arm rests.
The tray can only be mounted on a x:panda
equipped with arm rests.
B
A
C
G
B
GB
TRAY, TWO-ROD
SYSTEM
ONLY FOR SIZE 1+2+3
A) Mounting and depth adjustment
B) Width adjustment
C) Angling the tray, by angling the arm rests.
A
C
B
The tray can only be mounted on a x:panda
equipped with arm rests mounted at the
same height and angle.
12
GB
ARM REST FOR
TRAY
ONLY FOR SIZE 1+2+3
A) Depth adjustment
B) Angle adjustment
A
The arm rests can only be mounted on a
x:panda equipped with tray.
GB
B
TOYBAR FOR TRAY
ONLY FOR SIZE 1+2+3
A) Angle ajdustment
The toybar can only be mounted on a
x:panda equipped with tray.
G
B
A
GB
GRIP HANDLE FOR
TRAY
ONLY FOR SIZE 1+2+3
A) Angle adjustment
The grip handle can only be mounted on
a x:panda equipped with tray.
A
13
GB
B
VESTS & BELTS
All vests and belts with 25 mm strap can be
mounted on the seat. We recommend to use the
fixlocks or belt guidances on the chair.
Fixlocks:
Use the fixlock (A) mounted on the chair to fasten and adjust all vests and belts. An extra 40
mm fixlock can be mounted on the size 4 seat
if needed (B).
A
Belt guidance:
Guide the beltstraps through the prepared slots
(C) in the seat.
C
A
GB
To mount vests and belts the correct way, it might
be necessary to mount extra fixlock fittings. The
fittings are mounted on the top of the back and
are able to lift the straps away from the shoulders
of the user.
D
G
B
C
FIXLOCK FITTINGS
* Mount the fittings in the lower holes (A) to get
a higher mounting of the straps.
* Mount the fittings in the top holes (B) to get a
lower mounting of the straps.
B
A
* Mount the fittings as shown on drawing (C)
to get a larger distance between the fittings.
* Mount the fittings as shown on drawing (D) to
get a smaller distance between the fittings.
14
GB
SEAT WEDGES
Depth adjustment:
Remove the seat cushion and release the wedges from the velcro in the seat.
Flip up the velcro (A) and place the wedges at
the desired depth position. Replace the seat
cushion.
GB
A
SEAT STRAP
G
B
Depending on the desired leg abduction the
seat strap is mounted in one of the three holes
in the seat.
Adjustment:
Flip up the strap in one of the sides and adjust
the length of the strap. Fold down the strap to
fasten with the velcro.
15
GB
FOAM BACK PLATE
The foam back plate can be adjusted to fit the
gap beneath the back.
* If necessary, cut the foam plate with a knife
to make it fit the gap.
* Place the foam plate on the back.
GB
COVER PLATE
ONLY FOR SIZE 4
The cover plate fits the gap beneath the back.
* The cover plate is mounted in the slot in the
back
G
B
GB
LUMBAR SUPPORT
Remove the cushion to mount the lumbar support on the back
* Place the lumbar support in position
16
GB
NON-DYNAMIC GAS
SPRING
ONLY FOR SIZE 1+2+3
The standard gas spring can be replaced with a
non-dynamic gas spring.
B
Loosen the handle (A) to angle the back.
A
Please be aware not to get your fingers
caught betweeen the gas spring and the
seat when angling (B).
GB
FIXED ROD
G
B
The standard gas spring can be replaced with
a fixed rod.
17
GB
X:PANDA MOUNTED
ON HIGH-LOW:X
To mount the seat:
The interface and the footrest bar must be
replaced on the old High-low frames.
Place the seat adapter in the interface and push
it all the way back, until it "clicks" into place.
Lock the red handle (B) to secure the stability
of the seat.
A
Do not use the first hole it „clicks” into. This
is just the „safety hole” which will „catch”
the seat if the knob accidently should pop
out of its correct hole.
B
To dismount the seat:
Unlock the red handle (B). Pull out the knob (A),
pull the seat forward, and lift at the same time.
G
B
18
GB
MOUNTING THE
SEAT ON THE HIGHLOW:X SIZE 3
ONLY SIZE 3+4
Mount the x:panda seat directly on the Highlow:x size 3 frame.
* Lead the enclosed screws though the seat
frame (A) from below. Make sure the seat is
securely fastened before use.
2x
* Remove the screws at dismounting
2x
A
G
B
19
GB
A
GROWTH FROM
ONE SIZE TO
ANOTHER - WIDTH
ADJUSTMENT
Follow this description to perform a smooth
adjustment of the seat width. Also read the instructions on the next page concerning depth
adjustment.
Dismount the hip supports (A) at both sides.
Dismount the metalplate (B). Remove the 4 bolts
(C) and swing away the back.
Left chair side:
Pull the leg support forward but do not remove
any bolts not described.
B
Remove the bolt (D).
Remove the bolt (E).
Remount at the desired width position and replace the bolts (D) and (E). Do not fasten the
bolts completely.
Size
1+2+3
Right chair side:
Remove the bolts (D) and (E) at the opposite
side of the chair.
E
G
B
Place the seat spacer (F).
D
C
Remount at the same width position as the opposite side and replace the bolts (D) and (E).
Size 4
E
Remount the bolts (C).
Both chair sides:
Fasten all bolts (C) (D) and (E) at both sides of
the seat.
Do not loosen or remove any bolts not
described above.
To prevent at mix up of bolts, we recommend to keep the removed bolts
together with the removed part, e.g.
the hip supports.
The carer should check and tighten all
bolts at least every month.
F
20
GB
GROWTH FROM
ONE SIZE TO
ANOTHER - DEPTH
ADJUSTMENT
Follow this description to perform a smoothly
adjustment of the seat depth. Also read the instruction on the previous page concerning width
adjustment.
Remove the two bolts (A) at both sides of the
chair.
A
Take a firm hold of the backrest.
Remove the two bolts (B).
Remount at the desired depth position and replace and fasten the bolts (A) and (B).
Do not loosen or remove any bolts not
described above.
G
B
To prevent at mix up of bolts, we recommend to keep the removed bolts
seperated.
B
The carer should check and tighten all bolts
at least every month.
21
GB
A
B
C
REPLACEMENT OF
BACK - ONE SIZE
TO ANOTHER
Loosen the two bolts (A)
B
Remove the two cross-point screws (B)
Remove the six bolts (C)
Remove the cover plate
Remove the back stop device (D) (only size
1+2+3). Pull up the back plate (E) and remove.
Replace the desired back plate (E) and push it
all the way down.
E
Remount the back stop device (D) (only size
1+2+3).
Remount the cover plate.
Fasten the 6 bolts (C)
Remount the two cross-point screws (B).
G
B
Fasten the two bolts (A).
D
Finally check that the back moves smoothly up
and down.
22
GB
THE X:PANDA SEAT
ON HIGH-LOW:X
FRAMES
The x:panda seat adjusts in 3 different widths.
Each seat in each width can be mounted on
different sizes of High-low:x frames. Please see
the chart below to find the right size frame for
your seat.
● Recommended
○ Possible
x:panda
High-low:x
indoor
size 1
Gas
Pow
x:panda size 1S
●
x:panda size 1M
x:panda
High-low:x
indoor
size 3
Pow
Pow
Pow
●
●
●
●
●
●
●
x:panda size 1L
●
●
●
●
x:panda size 2S
●
●
●
●
x:panda size 2M
●
●
●
●
x:panda size 2L
●
●
●
●
x:panda size 3M
x:panda size 3L
○
○
○
○
○
○
Hyd
x:panda
High-low:x
outdoor
size 1
Gas
x:panda size 3S
Gas
x:panda
High-low:x
indoor
size 2
○
○
○
Gas
Pow
Hyd
G
B
●
●
●
●
●
●
●
●
●
●
●
●
x:panda size 4S
●
x:panda size 4M
●
x:panda size 4L
●
23
x:panda
High-low:x
outdoor
size 2
GB
THE X:PANDA
SEAT ON PANDA
FUTUTRA HIGHLOW FRAMES
Mount a new interface on the High-low frames to
mount the x:panda seats. Follow the instruction
which follow the interface.
Panda Futura
High-low indoor
size 1
G
B
Panda Futura
High-low outdoor
size 1
Gas
Pow
Gas
Pow
x:panda size 1S
●
●
●
●
x:panda size 1M
●
●
●
●
x:panda size 1L
●
●
●
●
x:panda size 2S
●
●
●
●
x:panda size 2M
●
●
●
●
x:panda size 2L
●
●
●
●
24
GB
THE X:PANDA
SEAT ON COMBI
FRAME:X
The x:panda seat adjusts in 3 different widths.
Each seat in each width can be mounted on
different sizes of Combi frames. Please see the
chart below to find the right size frame for your
seat.
● Recommended
○ Possible
Combi Frame:x size 1
Combi Frame:x size 2
Combi Frame:x size 3
Combi Frame:x size 4
20”
22”
24”
12½"
20”
22”
24”
12½"
20”
22”
24”
12½"
20”
22”
24”
12½"
x:panda size 1S
●
●
●
●
○
○
○
○
○
○
○
○
○
○
○
○
x:panda size 1M
●
●
●
●
○
○
○
○
○
○
○
○
○
○
○
○
x:panda size 1L
●
●
●
●
●
○
○
○
○
○
○
○
○
x:panda size 2S
●
●
●
●
●
○
○
○
○
○
○
○
○
x:panda size 2M
●
●
●
●
●
●
●
●
●
○
○
○
○
x:panda size 2L
●
●
●
●
●
●
●
●
○
○
○
○
x:panda size 3S
●
●
●
●
●
●
●
●
●
●
●
●
x:panda size 3M
●
●
●
●
●
●
●
●
x:panda size 3L
●
●
●
●
●
x:panda size 4S
●
●
●
●
x:panda size 4M
●
●
●
●
x:panda size 4L
●
●
●
●
●
●
●
25
G
B
GB
THE X:PANDA SEAT
ON BUGGY FRAME
The x:panda seat adjusts in 3 different widths.
Each seat in each width can be mounted on
different sizes of buggy frames. Please see the
chart below to find the right size frame for your
seat.
G
B
Buggy frame
Serval
size 1
Buggy frame
Serval
size 2
Buggy frame
Stingray
x:panda size 1S
●
●
●
x:panda size 1M
●
●
●
●
●
●
●
●
●
x:panda size 1L
x:panda size 2S
x:panda size 2M
x:panda size 2L
x:panda size 3S
x:panda size 3M
x:panda size 3L
x:panda size 4S
x:panda size 4M
x:panda size 4L
26
●
i
The chair is approved according to ISO
7176/19-2001 and 16840-4:2009.
GB
TRANSPORTATION
IN MOTOR
VEHICLES
x:panda seat is approved for transporting
the user in motor vehicles. Please look at
MEASURES in the back of this manual for
the max load. indication.
The x:panda seat on a R82 frame, is approved
for transporting users in motor vehicles, when
The approval is not valid on specially made the chair and frame are placed in forward-facing
chairs and frames.
position.
The user should transfer to the vehicle seat Detailed information about configurations for
and use the vehicle-installed restraints
frames and x:panda seat, max. load/user weight
system whenever possible.
and transportation can be found in the overview
Seat and frame must be placed in a for- "frame_and_seat_combination.pdf".
ward-facing position, when used as a seat
in a motor vehicle. Use an approved 4-point The overview can be found here:
strap-type tiedown system according to
http://www.r82.org/media/102124/frame_and_
ISO 10542-2.
seat_combination.pdf
Use an approved 3-point belt according to
ISO 10542-1 in the wheelchair. Restraints All information in this chapter must be carried
should not be held away from the body by through to maintain safety.
wheelchair components such as armrests
or wheels. It is NOT enough only to use a
hipbelt or vests and belts not approved by
G
Restraints should not
ISO 10542.
be held away from
B
body by wheelchair
The front wheels need to be turned under
components such as
armrests or wheels
the frame so as to be in line wit the frame
before fixation.
All accessories must be removed from the
wheelchair and secured separately in the
vehicle. Accessories which can not be removed out of consideration of the user, must
be secured to the wheelchair but positioned
away from the user with energy-absorbing
padding placed between the accessories
and the user.
The product should be inspected by the
dealer before re-use following involvment
in any type of vehicle collison.
The following instructions on how to prepare the seat and frame, must be carried
out before transportation.
27
GB
POSITION THE
BACK BEFORE
TRANSPORTATION
The bush (A) on the gasspring (B) must be handtightened up against the gasspring house before
transportation.
B
The back MUST be placed in vertical
position and the bush (A) MUST be handtightened before transportation.
A
GB
G
B
TRANSPORT
FITTINGS ON A
BUGGY FRAME
Secure the x:panda seat on a buggy frame in
a vehicle:
A
* Mount the 4-point strap-type tiedown system
in the vehicle. (Follow the manufactures
instructions)
* Mount the two fittings (A) with the symbol (B)
on both sides of the pushchair frame.
* Secure the chair to the vehicle, using the 4point strap-type tiedown system. Use either
a hook or a strap in the fitting (A).
B
Use a 4-point strap-type tiedown system
approved according to ISO 10542-2 or
SAE J2249.
28
GB
TRANSPORT
FITTINGS ON THE
COMBI FRAME
2x
2x
A
B
Placing the Combi Frame in the vehicle:
1.By use of a 4-point strap system, the frame
is secured in the vehicle. (Follow instructions
from the manufacturer of the vehicle).
C
A
A 4-point strap-system, approved according to ISO 10542-2 or SAEJ2249, must
be used.
Size 1+2
Size 3+4
On the rear of the frame, fitting A:
2.* Remove the plugs.
* Place the fittings (A) on the rear bar.
* Mount with the enclosed 6 mm long bolts
and nuts. (Note the placement for the different
sizes.)
D
On the front of the frame, fitting B:
3.* Remove the plugs (D) in the side rails.
* Slide the thread block into the side rails.
* Mount the plugs (D) again.
* Place the fitting (B) over the thread block.
* Tighten with the enclosed 6 mm. bolts and
washer through the holes in the thread block.
It is important that the 'legs' on the fitting (B)
is placed in the holes in the side rails.
The fitting (B) can be turned upwards (as on
the drawing) or downwards if you wish.
4.The wheelchair is fastened in the vehicle by
use of a 4-point strap-system. Either a hook
or a strap can be used for fastening the fittings
(A) and (B).
B
G
B
Stick the enclosed stickers (C) on the four fittings
(A) and (B).
29
GB
SECURE THE
PRODUCT IN THE
VEHICLE
30°
* Mount the 4-point strap-type tiedown system in the vehicle. (Follow the manufacture
instructions)
B
* Secure the pushchair to the vehicle, using the
4-point strap-type tiedown system. Use either
a hook or a strap in the fitting.
15°
15°
Use a 4-point strap-type tiedown system
approved according to ISO 10542-2 and
SAE J2249.
40 cm
65 cm
Position inside vehicle:
G
B
* Remove all accessories from the pushchair
before transportation.
1,2 m
* Place the child in forward-facing position.
Be aware of the recommended safety zone
when moving children in vehicles.
30
GB
SECURE THE CHILD
IN THE PRODUCT
* Mount a hip-belt in the belt fittings in the seat
and fasten the user.
* Use the 3-point belt as shown on drawing to
secure the user. The belt restraints should
be adjusted as tightly as possible, consistent
with user comfort. Further the belt webbing
should not be twisted when in use.
55°
Use a hip-belt and an approved 3-point belt
according to ISO 10542-1 or SAE J2249.
G
B
31
A
GB
B
XXXXXX
Max load: xxx kg
DMR ver.: XXXX
Max load: xxx kg
Art. no.: XXXXXXX
Product: XXXXXXX - Size X
PRODUCT
IDENTIFICATION
(XX)XXXXXXXXXXXXXX(XX)XXXXXX(XX)XXXXXX
x:panda seat
A)Serial number
The label is placed in the seat under the
cushion to the left.
A
B
B)Manufacturer
The label is places in the seat under the
cushion to the right.
High-low:x indoor and outdoor frame
A) Serial number
The label is placed on the left side of the
frame.
B
B
A
B) Manufacturer
The label is placed on the left side of the
frame.
A
G
B
Combi Frame:x
A) Serial number
The label is placed left on the front cross bar
beneath the seat.
A
B) Manufacturer
The label is placed far left on the front cross
bar beneath the seat.
B
Pushchair frame
A) Serial number
The label is placed on the top cross bar below
the seat.
B) Manufacturer
The label is placed on the cross bar at the left
rear wheel.
A
B
32
GB
PRODUCT
IDENTIFICATION
A
B
XXXXXX
Max load: xxx kg
DMR ver.: XXXX
Max load: xxx kg
Art. no.: XXXXXXX
Product: XXXXXXX - Size X
(XX)XXXXXXXXXXXXXX(XX)XXXXXX(XX)XXXXXX
Multi Frame
A) Serial number
The label is placed left on the front cross bar
beneath the seat.
B
B) Manufacturer
The label is placed far left on the front cross
bar beneath the seat.
A
Multi Frame:x
A) Serial number
The label is placed left on the front cross bar
beneath the seat.
B) Manufacturer
The label is placed far left on the front cross
bar beneath the seat.
G
B
Strong Base
A) Serial number
The label is place on the underside of the
frame to the left.
A
B
B) Manufacturer
The label is place on the underside of the
frame to the left.
A
33
B
MEASUREMENTS
GB
x:panda
Size 1
mm (inch)
G
B
Seat width (A)
x:panda
Size 2
mm (inch)
x:panda
Size 3
mm (inch)
x:panda
Size 4
mm (inch)
160, 200, 240
(6¼,7¼,9¼")
70, 90, 110
(2¾, 3½, 4¼")
200, 240, 280
(7¼,9¼,11")
100, 120, 140
(4, 4¾, 5½")
260, 310, 360
(10¼,12,14")
120, 145, 170
(4¾, 5¾, 6¾")
340, 400, 460
(13¼, 15½, 18")
130, 190, 250
(5, 7½, 9¾")
270-370 (10½-14½")
320-420 (12½-16½")
350-470 (13½-18¼")
490-680 (19-26½")
Back angle (a)
Abduction angle, each leg (a1)
* size 1 in the smallest position
230 (9")
310, 350, 390
(12, 13½, 15¼")
-5° - +30°
0° - 15° *
0° - 8°
280 (11")
380, 420, 460
(14¾, 16¼, 18")
-5° - +30°
0° - 15°
-
330 (12¾")
470, 520, 570
(18¼, 20¼, 22¼")
-5° - +30°
0° - 15°
-
350 +50 (13½ +2")
590, 650, 710
(23, 25¼, 27½")
-5° - +30°
0° - 15°
-
Weight
Max load / user weight on
Max load / user weight at transportation
6,5 kg (14,5 lb)
45 kg (99 lb)
45 kg (99 lb)
8,5 kg (18,5 lb)
50 kg (110 lb)
50 kg (110 lb)
11 kg (28,5 lb)
60 kg (132 lb)
57 kg (125,5 lb)
13 kg (28,5 lb)
80 kg (176 lb)
57 kg (125,5 lb)
Width, thighs (A1)
Seat depth (B)
Back height (C)
Back width, top (F)
Total width, both legs in max abduction (G)
160-260 (6¼-10¼")
220-330 (8½ -12¾")
260-390 (10¼-15¼")
Further information regarding max. load/user weight and transportation:
www.R82.com/files/archive/Publications/Pdf/Chart_transport.pdf
34
380-530 (14¾-20½")
GB
Seat:
Foam:
Cover:
Frame:
TECHNICAL DATA
PA6 - recyclable
Flameproof
Gemma
Powderpainted aluminium
GB
PRODUCER
R82 A/S
Parallelvej 3
8751 Gedved
Denmark
GB
DISTRIBUTOR
Please find your distributor on www.R82.com
G
B
35
GB
MAINTENANCE
The x:panda cushion is removable and the cover can be washed at max. 40°. The condition of
the foam cushion should be checked at least every six months and replaced if necessary. It is
important to keep the frame clean to maintain the validity of the chair.
The carer should check and oil the swing away parts occationally - at least every 6
months.
Use a dry cloth, on a weekly basis, to wipe off filth and dirt from the wheels. Do not use any
cleaning materials containing chlorine or methylated spirit.
The x:panda has to be checked and tightened by a qualified technician at least every 6
months to avoid failures.
Do not expose the gasspring to pressure, high temperatures or perforation.
Any adjustments and addition of accessories which are not described in this manual, must
only be made by authorized R82 personnel. Vests and belts must be mounted according to
the instruction provided with the products.
G
B
The carer should check and refill the tyres for air at least once a month. Air pressure:
High-low:x outdoor frame. Front: 35 PSI/250 kPa, rear: 40 PSI/2,5 bar
Wheelchair frame. Wheels: 110 PSI/250 kPa
Pushchair frame. Front: 36 PSI/2,5 bar, rear: 36 PSI/2,5 bar
36