CHRONO
i n s p i r e d by n at u r e
//
BREAK NEW BOUNDARIES WITH THE
U LT R A H I G H - P E R F O R M A N C E C H R O N O
driven by the elements
//
f lyo z o n e . c o m
ozonekites
Checking Bridles and Speed System for Stretch, Shrinkage or Wear
This is a high end performance product. The Bridle lines and Speed System must be checked after every 60 hours flying time, if they are worn or
are not to factory specifications (+ or - 15mm) they must be replaced or the kite will not perform as designed. Use the measurements on the
next page to check your Bridle lengths.
Recommendations
Speed System Zero position
If you require new Bridle lines please get in touch with the shop/dealer you
purchased the kite from and they can order individual lines or a full set.
If the difference between the three ends is bigger than 15mm you should
replace the Speed System.
• Open your kite in a large space, big enough to spread your kite out.
• Use a tape measure to measure the bridles as in the picture.
• Print out the sheet and write down any differences.
measure bridles
Check your Speed System lines by levelling the front and back line pigtails,
then tension the three top ends of the Speed System where the bridle lines are
attached, they should be at the same level + or - 15mm, as in the picture.
align
if difference bigger
than 15mm, replace
speedsystem
chrono BRIDLE CHECK SHEET.
ALL MEASUREMENTS IN MM
9M 12M15M18M
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
AM1
AM2
AM3
AM4
AR1
AR2
1230
1076
1000
1178
1065
1033
1133
959
846
772
676
1406
1094
1172
1094
2187
1718
1441
1259
1161
1356
1212
1163
1261
1047
907
808
690
1624
1263
1353
1263
2526
1984
1616
1412
1303
1521
1360
1305
1415
1175
1019
908
776
1815
1412
1513
1412
2824
2219
1774
1550
1431
1669
1493
1433
1553
1291
1120
999
854
1988
1546
1656
1546
3092
2429
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
BM1
BM2
BM3
BM4
BR1
BR2
1214
1057
976
1156
1040
1006
1125
952
838
772
663
634
1406
1094
1172
1094
2187
1718
1421
1233
1131
1329
1181
1130
1252
1039
899
810
676
643
1624
1263
1330
1230
2526
1984
1591
1381
1268
1489
1324
1268
1403
1165
1009
908
760
725
1815
1412
1480
1370
2824
2219
1746
1517
1393
1634
1454
1392
1540
1280
1108
1000
836
798
1988
1546
1623
1504
3092
2429
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
CM1
CM2
CM3
CM4
CR1
CR2
1299
1134
1040
1219
1092
1043
1181
1002
879
961
842
787
1406
1094
1172
937
2187
1718
1521
1326
1208
1404
1245
1175
1319
1100
947
1030
884
815
1624
1263
1353
1082
2526
1984
1701
1483
1351
1571
1393
1316
1476
1231
1061
1155
994
918
1815
1412
1513
1210
2824
2219
1867
1627
1483
1724
1529
1445
1620
1352
1166
1268
1092
1009
1988
1546
1656
1325
3092
2429
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K12
KML1
KML2
KMU1
KMU2,3
KMU4
KR1
1330
1063
847
1141
931
812
873
698
609
637
551
1250
1015
1406
937
781
1982
1582
1272
1005
1330
1066
893
966
743
618
641
521
1443
1173
1624
1082
902
2153
1775
1429
1130
1494
1199
1006
1088
840
700
727
592
1613
1311
1815
1210
1008
2313
1949
1570
1242
1642
1318
1107
1199
927
774
805
657
1767
1436
1988
1325
1104
2456
rigging diagram