3 You are installing your first thermostat You can watch this installation on: http://netatmo.com/video3 Warning Warning! вЂў Read carefully these instructions before starting the installation. вЂў The Netatmo Thermostat must be installed according to applicable standards. вЂў Before any intervention, make sure power is turned off. In the box Thermostat Mobile stand Relay Boiler adapter Mounting Plate Color Adhesives (Trim plate)* (Mains adapter)* 3 AAA batteries 4 screws 4 screw anchors 1 USB cable (Tape)* (Cover)* * not used in this setup Identify Open the boilerвЂ™s hood using, if necessary, its instructions manual. Your relay will control your boiler when plugged in the corresponding terminals. Identify the thermostat terminals in the boiler, labeled LS-LR, TA or COM-NO. They may be identifiable thanks to a shunt between the two thermostat terminals. LS / LR or TA or COM / NO You have to remove the shunt Thermostat terminal Usually black or grey wires Connect the black and grey wires of the boiler adapter in place of the shunt you removed from the thermostat terminals in the boiler. Electric Power The relay receives 220V power from your boiler. The power terminals of your boiler are labeled L/N or P/N. - If your boiler has available power terminals, connect the blue and brown wires of your boiler adapter in those terminals. -Otherwise, you can connect the blue and brown wires of the boiler adapter in the power terminals from which the boiler itself receives power. The wires of the boiler must remain connected. P/N or L/N Our forum can help you identify the correct terminals : forum.netatmo.com In doubt, please send a picture of your wiring at photo@netatmo.com, and our support team will help you identify the right terminals. 220V Power supply terminals Blue and brown wires Setting the relay The boiler adapter should be placed as far as possible from metallic items (wiring, pipes, electrical gridвЂ¦). 30 cm You can fix the boiler adapter to the wall either using the double-sided tape or screw it. or Testing the relay 1 Connect the relay into the boiler adapter. 2 Switch the power supply back on. 3 The relay blinks blue. Note: if the relay does not blink after turning the power back on, it is not properly powered. Please check how the blue and brown wires are wired. Do not forget to switch off the power supply before any intervention. Testing the relay 1 2 Briefly push the relayвЂ™s button. The relay lights up in blue and switches the boiler on. 3 4 Push again the relayвЂ™s button. The relay turns its light and the boiler off. Note: if the boiler doesnвЂ™t switch on when the blue light is on, the relay is incorrectly wired to the boiler. In this case, check where the grey and black wires are connected. In doubt, please read your boilerвЂ™s instructions manual at the В«room thermostatВ» section. Thermostat 1 2 The Thermostat displays the start screen and searches for the relay. Insert the batteries in the Thermostat. + 21 20 5 0 + Setpoint Temperature Measured Temperature If the Thermostat has found the relay, it displays the setpoint and the room temperatures. or 21 20 5 0 If the Thermostat hasnвЂ™t found the relay, it displays the В«!В» symbol. In this case, move the relay closer to the Thermostat and wait until the В«!В» symbol disappears. Test 1 Tap a few times the top of the Thermostat until the screen shows В«В MAXВ В». The Thermostat switchs on the boiler. clic + 21 20 + 5 0 20 0 2 Tap the bottom of the Thermostat until you reach В«В OFFВ В». The Thermostat switchs off the boiler. + + 20 20 0 clic 0 Customisation 1 You can choose to customise your Thermostat by using one of the colour adhesives. 2 Take off the outer frame of the adhesive. 3 Stick it on the back of your Thermostat. Location or Set the Thermostat on the mounting plate. Clip the Thermostat on its mobile stand and place it on a shelf in the living room. 1m 1m + 18 22 5 1.5 m More than 1m from the openings 1.5m high Away from any cold or heat source App To control and program your Thermostat from your smartphone, tablet or computer, visit: http://thermostat.netatmo.com PC / Mac Smartphone / Tablettes Specifications SIZE Thermostat : 83x83x22 mm DESIGN Designed by Starck. Translucent minimalist plexiglass cube. 5 interchangeable colors in the box. SENSORS AND MEASUREMENTS TempГ©rature (measurement): Ranges from 0В°C to 50В°C Accuracy: +- 0.5В° C TempГ©rature (setpoint): Ranges from 7В°C to 30В°C Increment: 0.5В°C Unit: В°C E-INK DISPLAY Energy efficient, longer battery life and optimal readability. FREE APP, LIFETIME SUPPORT No subscription fee. App available on the App Store and on Google Play. Free access to your online personal dashboard. Accessible from multiple devices. WIRELESS SPECIFICATIONS Wi-Fi 802.11 b/g/n compatible (2.4GHz). Supported security: Open/WEP/WPA/ WPA2-personal (TKIP and AES). Wireless connection between thermostat and relay: radio long range 100m. POWER AND BATTERIES 3 AAA batteries. 1 year battery life. SETUP AND COMPATIBILITY Compatible with gas, fuel and wood boilers. Switching current: max 4 A Switching voltage: max 250 VAC Switching power: max 120 W COMPATIBLE WITH IPHONE AND IPAD iPhone 4, iPhone 4s, iPhone 5, iPhone 5c / 5s iPad mini, iPad mini with Retina display, iPad 2, iPad (3rd generation), iPad (4th generation), iPad Air iPod touch (5th generation) COMPATIBLE WITH ANDROID SMARTPHONE Android 4.0 required EU Declaration of Conformity We, Netatmo, declare that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. EU Declaration of Conformity We, Netatmo, declare that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Safety warnings This device must be installed according to the applicable norms. Use only with supplied power plug adaptor and boiler adaptor. This device is for indoor use only. Before inserting the batteries, check that the contacts in the device and on the batteries are clean, and clean them if necessary. Note the polarity (+/-) when inserting the batteries. Do not throw the batteries into a п¬Ѓre, short-circuit it or dismantle it. Keep children away from Canadian Compliance Statement batteries. Seek medical attention immediately if a battery is swallowed. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the two conditions: (1) this device may not Do not attempt to repair the device yourself; an after-sales service isfollowing available. cause interference, and (2) this device must accept any interference, including Any changes or modifications to this unit not expressly the operation party responsible for interferenceapproved that may causeby undesired of the device. Cet appareil est conforme aux normes CNR exemptes de licence d'Industrie compliance could void the userвЂ™s authority to operate the equipment. Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) cet FCC Radiation Exposure Statement Thermostat and relay insulation: class II devices. appareil ne doit pas provoquer d'interfГ©rences et (2) cet appareil doit accepter This equipment complies with FCC RF radiation exposure limits set forth for an toute interfГ©rence, y compris celles susceptibles de provoquer un fonctionnement uncontrolled transmitter shouldfor be installed andpersons operated Thisenvironment. device isThisnot intended use by (including children) with reduced physical, sensory non souhaitГ© de l'appareil. with a minimum distance of 20 centimeters between the radiator and your Thisknowledge, Class B digital apparatus complies with Canadian or mental capabilities, or lack of experience and unless they have ICES-003. been given body and must not be co-located or operating in conjunction with any other Cet appareil numГ©rique de la classe B est conforme Г la norme NMB-003 du antennasupervision or transmitter. Thisor equipment compliesconcerning with Part 15 of theuse FCC Rules. instruction of the appliance Canada. by a person responsible for their safety. Operation is subject to the following two conditions: This device and its antenna(s) must not be co-located or operating in be interference, supervised (1) This Children device may notshould cause harmful and to ensure that they do not play with the appliance. conjunction with any other antenna or transmitter. (2) This device must accept any interference received, including interference Legal notice Cet appareil et son antenne (s) ne doit pas ГЄtre co-localisГ©s ou fonctionnant en that may cause undesired operation. conjonction avec une autre antenne ou transmetteur. вЂњMade for iPodвЂќ, вЂњMade for iPhoneвЂќ, вЂњMade for iPadвЂќ mean that an electronic accessory has Taiwan Wireless Statements been designed to connect speciп¬Ѓcally to iPod, iPhone and iPad and has been certiп¬Ѓed by the з„Ўз·љиЁе‚™зљ„и¦е‘ЉиЃІж�Ћ developer to meet Apple performance standards. жњ¬з”ўе“Ѓз¬¦еђ€дЅЋеЉџзЋ‡й›»жіўиј»е°„жЂ§й›»ж©џз®Ўзђ†иѕ¦жі•В з¬¬гЂёдєЊжўќгЂЃз¬¬гЂёе››жўќз‰ Apple is not responsible for the operation of жўќж–‡и¦Џе®љ:В this device or its compliance with safety and regulatory standards. 1.В з¶“ећ‹ејЏиЄЌи‰еђ€ж јд№‹дЅЋеЉџзЋ‡е°„й »й›»ж©џпјЊйќћз¶“иЁ±еЏЇпјЊе…¬еЏёгЂЃе•†и™џж€–дЅї з”ЁпїЅеќ‡дёЌеѕ—ж“…и‡Єи®Љж›ґй »зЋ‡гЂЃеЉ е¤§еЉџзЋ‡ж€–и®Љж›ґеЋџиЁиЁ€д№‹з‰№жЂ§еЏЉеЉџиѓЅгЂ‚В Please note that the use of this accessory with iPhone may affect wireless performance. 2.В дЅЋеЉџзЋ‡е°„й »й›»ж©џд№‹дЅїз”ЁдёЌеѕ—еЅ±пїЅйЈ›и€Єе®‰е…ЁеЏЉе№Іж“ѕеђ€жі•йЂљдїЎпј›з¶“з™ј зЏѕжњ‰е№Іж“ѕзЏѕи±Ўж™‚пјЊж‡‰з«‹еЌіеЃњз”ЁпјЊдё¦ж”№е–„и‡із„Ўе№Іж“ѕж™‚ж–№еѕ—з№јзєЊдЅїз”ЁгЂ‚В е‰Ќй …еђ€жі•йЂљдїЎпјЊжЊ‡дѕќй›»дїЎжі•и¦Џе®љдЅњжҐд№‹з„Ўз·љй›»йЂљдїЎгЂ‚В дЅЋеЉџзЋ‡е°„й »й›»ж©џй €еїЌеЏ—еђ€жі•йЂљдїЎж€–е·ҐжҐгЂЃз§‘еёеЏЉй†«з™‚з”Ёй›»жіўиј»е°„жЂ§ й›»ж©џиЁе‚™д№‹е№Іж“ѕгЂ‚ Complies with IDA Standards V16 Copyright Netatmo В© 2013 All rights reserved. Reproduction and distribution prohibited without written authorization from Netatmo. V1_EN