PAUHF005HG with FREESCALE MW6S010NR1 and - Ital

ital mec
PAUHF005HG
Objective data sheet
COSTRUZIONI ELETTROMECCANICHE
Power Amplifier Section 20W
20W UHF
UHF
Designed for analog and digital applications.
This amplifier is suitable for DVB-T/H, ATSC or any
analog TV standard.
•
•
•
•
•
•
•
470 - 860 MHz
Pout : 5 Wrms DVB-T/H – 20Wps Analog TV
Gain : 28 dB
Class AB
Devices : 2 x Freescale MW6S010NR1
1 Hittite HMC453ST89E
Supply : 28Vdc typ.
Dimensions (LxWxH): 165 x 78 x 21 mm
6,49”x 3,07”x 0,82”
Absolute maximum ratings
Parameter
Voltage supply
Supply current
Operating Temperature range
Storage Temperature range
Load Mismatch (full power, all phase angle)
Value
30 Vdc
3A
0
+85
-30
+90
2:1
Symbol
Vs
Is
°C Note 1
°C
Note2
Electrical Specifications
Parameter
Frequency range
Power gain
DVB-T/H Pout with IMD ≤ -30 dBc
Analog TV Pout with IMD ≤ -50 dBc
(Red Field)
Min.
470
29
4
Typ.
Max.
862
30
5
7
Units.
MHz
dB
Wrms
15
20
30
Wps
Note
Full band
No
precorrection
No
precorrection
Rev. 01 – 04 June 2014 - Issued by: M. Rossi
ITALMEC s.r.l. strada delle Conce, 7 - 05018 Orvieto (TR) – ITALY – tel. E fax +39 (0)763 393912
Internet : www.ital-mec.com E-mail : italmec@ital-mec.com
ital mec
PAUHF005HG
Objective data sheet
COSTRUZIONI ELETTROMECCANICHE
Supply voltage
Pout @ 1dBc
Quiescent current
An. TV Id @ Pout = 20Wps (black field)
DVB Id @ Pout = 5 Wrms
Load mismatch
No power degradation
26
30
28
0.45
2.5
1.5
2:1
V
W
A
A
A
VSWR
Note 2
Typical performances
Low level Gain (Iq = 0.45 A Vdc = 28V)
Rev. 01 – 04 June 2014 - Issued by: M. Rossi
ITALMEC s.r.l. strada delle Conce, 7 - 05018 Orvieto (TR) – ITALY – tel. E fax +39 (0)763 393912
Internet : www.ital-mec.com E-mail : italmec@ital-mec.com
ital mec
PAUHF005HG
Objective data sheet
COSTRUZIONI ELETTROMECCANICHE
25,0
-20
23,0
-22
21,0
-24
19,0
-26
17,0
-28
15,0
-30
13,0
-32
11,0
-34
9,0
-36
7,0
-38
5,0
474
522
570
618
666
714
762
810
Shoulders [dBc]
Efficiency [%]
DVBVB-T Performances @ Pout = 5W
5Wrms
-40
858
Freq. [MHz]
Rev. 01 – 04 June 2014 - Issued by: M. Rossi
ITALMEC s.r.l. strada delle Conce, 7 - 05018 Orvieto (TR) – ITALY – tel. E fax +39 (0)763 393912
Internet : www.ital-mec.com E-mail : italmec@ital-mec.com
ital mec
PAUHF005HG
COSTRUZIONI ELETTROMECCANICHE
Objective data sheet
Mechanical Layout
Screws Type:
Screws point 1-2-3-4-5-6 M3 Socket head cap screws + 6 Split lock washers WZ ø 3.5
+ 6 Flat washers WZ ø 3.5
Screws point 7-8-9-10 M2.5 Socket head cap screws + 4 Split lock washers WZ ø 2.5
Thermal Compound
Recommended Dow Corning 340 ( heat sink compound ) or equivalent
Rev. 01 – 04 June 2014 - Issued by: M. Rossi
ITALMEC s.r.l. strada delle Conce, 7 - 05018 Orvieto (TR) – ITALY – tel. E fax +39 (0)763 393912
Internet : www.ital-mec.com E-mail : italmec@ital-mec.com
ital mec
PAUHF005HG
COSTRUZIONI ELETTROMECCANICHE
Objective data sheet
Application Note
Read carefully the following information, before design the system integration of this
amplifier. Please remember that Italmec engineers are available to help customers in any
design activity.
Note 1 (Thermal exchanger requirements)
Max operating temperature is measured very closed to the device flange and is referred to
the nominal operative condition. In case of different working conditions, this limit can be
different. Please contact our technical department for further information.
Note 2 (Load matching)
This amplifier can work without power reduction on a 2:1 VSWR load matching. In this
condition phase and temperature are irrelevant. Please, remember that this limit is valid only
for digital and analog signals. Other kind of modulation can drastically change this limit.
Note 3 (Protections)
In order to take the amplifier safe in any working conditions, please add these protections in
the final equipment.
a) Overdrive protection
If the input power of pallet exceed 2dB over the nominal, the device can be damaged, please
use an appropriate fast protection to reduce or switch off the input signal.
b) Reflected power protection (note 2),
A suitable protection system should switch off (or reduce) the input power in case of
excessive reflected power.
c) Thermal protection
Switch off supply voltage if device flange temperature exceeds 85C° when amplifier works at
full power.
IMPORTANT NOTICE
Italmec reserve the right to make changes to the product(s) or information contained herein without notice. Italmec assumes no
responsibility for any errors which may appear in this document. Warranty information applicable to the product identified
herein is available upon request. Nothing contained herein shall constitute a warranty,
representation or guarantee of any kind. Italmec expressly disclaims all other warranties, express and/or implied including but
not limited to warranties of merchantability, and of fitness for a particular purpose, use or application.
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of
Italmec.
Rev. 01 – 04 June 2014 - Issued by: M. Rossi
ITALMEC s.r.l. strada delle Conce, 7 - 05018 Orvieto (TR) – ITALY – tel. E fax +39 (0)763 393912
Internet : www.ital-mec.com E-mail : italmec@ital-mec.com

Download Report